After the router configured network, the EZVIZ smart home camera(s) can connect to the router's Wi-Fi by the function of One-Key Access.

Please follow the steps below:

1. Check if the RS2 is turned on: Press and hold the start button for 2 seconds. After 30 seconds, observe if the four-color indicator light of the device rotates and changes to a light yellow color, indicating that the device is turned on and functioning properly.

2. Verify if the RS2 lost contact during cleaning: If the robot loses contact with the docking station during cleaning, it may be due to the distance between them being too far. This temporary loss of connection does not affect the robot's normal operation. Once the connection to the docking station is restored, the RS2 will continue operating as usual.

3. Address internal errors: If the indicator light on the RS2 flashes red, it indicates an internal error in the robot's system. In such cases, press and hold the power button to restart the device. This can help resolve the internal error and restore normal functionality.

4. Address network fluctuations: If you experience network fluctuations, it may be helpful to restart the docking station. To do this, unplug the power supply, wait until the station screen is completely turned off, and then reconnect the power supply. This can help stabilize the network connection and ensure proper communication between the RS2 and the docking station.

If you continue to encounter issues or have any further concerns, please don't hesitate to reach out to our customer support for further assistance.

If you encounter a situation where the indoor monitor of the smart video doorphone reboots every time the lock is unlocked, please note that this appears to be a result of excessive lock power, as the power supply to the lock must not exceed 12V/1.1A to ensure smooth unlocking. If this is exceeded, please try the following to see if the problem can be resolved:

1. You can try lowering the screen brightness in settings > Screen and Image > Screen Brightness on the monitor.

2. If adjusting the brightness does not help, consider connecting a relay as described in the user manual. To do this, connect the relay to the lock terminals (indicated by a key symbol) on the back of the doorbell. Then, connect the other end of the relay to the positive and negative terminals of the lock.

3. Alternatively, you can try using a power supply with a 24V 1.5A input to see if that resolves the issue.

By following these steps, you should be able to address the rebooting issue with your indoor monitor. If the problem persists, please consider reaching out to our technical support team at support@ezviz.com for further assistance.

Possible reasons for not being able to enter the network configuration mode on the RS2 may include:

1. The RS2 is currently engaged in a mapping or cleaning task.

2. There might be an internal error within the RS2's system.

To resolve this issue, we recommend following these steps:

1. If you have attempted to enter the network configuration mode multiple times without success, try restarting the RS2.

2. Wait for the indicator light on the RS2 to rotate and change to a light yellow color before attempting any further operations.

If the problem persists or if you encounter any further difficulties, please don't hesitate to reach out to our customer support for additional assistance.

If you are experiencing issues with opening or closing the gate using the EZVIZ app or the indoor monitor—such as the mechanism attempting to close but then automatically reopening, or the gate opening and closing on its own—please follow the steps below:

1. Ensure that both the monitor and the doorbell have the latest firmware versions. You can check this by going to the "Settings" of each device separately in the EZVIZ mobile app, then navigating to "Device Information > Device Version".

2. On the monitor, go to "Settings > Screen and Image" and then adjust the "Gate-opening Command Time" to 3s, 2s, 1s, 0.3s, and 0.1s, respectively, to see if this resolves the issue.

If the problem persists, please reach out to our support team at support@ezviz.com and provide the following information:

   - The serial numbers of the indoor panel and the outdoor intercom (doorbell).

   - A photo of the gate motor nameplate.

   - A photo of the current wiring setup.

   - A video demonstrating the issue.

   - The e-manual of your gate motor.

By following these steps, we hope to help you resolve the issue with your gate.

After reset, the password will become “last 4 digits of SN” + ”verification code(6 upper case letters)”.

If you encounter a "wheel abnormal" prompt, please follow these steps:

1. Manually Rotate the Wheels: Check both wheels on the robot by manually rotating them. Look for any significant resistance or drag. If you notice high resistance in one or both wheels, inspect the wheel area for any debris or foreign objects that may be causing the issue.

2. Restart the Device: If there are no visible obstructions or if only one side has high resistance, try restarting the robot. After restarting, place the robot on a flat, even surface and initiate a cleaning cycle.

After completing these checks, see if the wheel issue is resolved. If you continue to experience problems, please contact our support team at cleaning.eu@ezviz.com for further assistance.

No, the smart video doorphone does not support RTSP or ONVIF. For optimal control and operation of the device, we recommend using the EZVIZ App.

Yes, you can integrate additional screens with your smart home video doorphone. Specifically, you can connect the doorphones with the SD7 smart screen. This is particularly beneficial for larger homes, as the SD7 extends the communication capabilities of your existing EZVIZ Video Doorphones.

By placing the SD7 in various areas of your home, such as the bedroom or kitchen, you can easily respond to doorbell rings without having to rush to a distant monitor. With just a few taps on the SD7, you can see who is at the door and grant access immediately.

No, the smart video doorphone does not support the addition of extra chimes.